ENRX I What is induction heating

The induction coil. What it is. 

Want more information on china high frequency induction screw rod quenching machine supplier? Feel free to contact us.

The induction coil (also known as ‘inductor’, or ‘coil’), is one of the most important components in an induction heating system. It is also one of the most neglected and misunderstood.The problem is that too many people see the coil as little more than a copper tube through which cooling water and an alternating current are fed. But nothing could be further from the truth. In fact, a correctly designed and professionally made coil has a decisive impact in several areas.

Correct process outcomes

The heating patterns, temperatures and heat penetration depths achieved during an induction heating cycle are directly and profoundly influenced by the coil’s physical characteristics. A poorly designed or manufactured coil yields poor results.

Cost control

A professionally designed and manufactured coil that is properly maintained has a much longer and more productive working life than its amateurish counter parts. Also, a correctly built and maintained coil helps minimize waste.

Overall system efficiency

ENRX induction heating systems are designed to operate with ENRX coils. Using the correct coils means significant long-term savings.

A crash course in coils

Designing and making induction coils is not easy. Here are just three of the many challenges that need to be overcome in order to make safe, efficient coils.

Through-flow rate

It is critical to achieve adequate flow of cooling water through the coil. This is especially true with high-power density coils, as low through-flow results in insufficient thermal transference. A booster pump may also be needed to maintain the desired flow. Good designers specify a purity level for the water, in order to minimize corrosion on the inside of the coil.

Magnetic flux concentrators

Concentrators focus the current in the coil area facing the workpiece. Without them, much of the magnetic flux may propagate around the coil. This flux could engulf adjacent conductive components. But, when concentrated, the flux is restricted to precise areas of the workpiece. Concentrators are made from laminations, or from pure ferrites and ferrite- or iron-based powders. Each material has its own pros and cons.

•  Laminations have the highest flux densities and magnetic permeability, and are less expensive than iron- and ferrite-based powders. Laminations are however stamped to a few standardized sizes and are therefore less flexible. They are also labour intensive to mount.
• Pure ferrites can provide outstanding magnetic permeability. But they suffer from low saturation flux density, and their brittleness makes them difficult to machine.
• Iron powders are easy to shape, offer high flux densities, and are easy to shape. However, care must be taken to protect against overheating, as internal losses or heat transfer from the heated workpiece mean such powders have a relatively low working temperature.

Impedance matching

It is necessary to achieve the correct impedance matching between the coil and the power source in order to use the latter’s full power. The designer must also consider that coils need five to ten times as much reactive as active power.

For more information, please visit china high frequency induction screw rod quenching machine factory.

What is 120KW High Frequency Induction Heating Machine Advantages?

120KW high frequency induction heating treatment machine does not need to heat the workpiece as a whole, but can selectively heat the parts, so as to achieve the purpose of reducing power consumption, and the deformation of the workpiece is not obvious. The fast heating speed of portable induction heater can make the workpiece reach the required temperature in a short time or even within 1 second. As a result, the surface oxidation and decarburization of the workpiece is relatively small, and most workpieces do not require gas protection.heat induction tool; bolt heater tool

The high frequency induction heating machine for stainless steel can adjust the surface hardening layer by adjusting the working frequency and power of the equipment as needed. As a result, the hardness, strength and toughness of the hardened layer are relatively high. After the heat treatment by the induction heating method, the toughness area of ​​the workpiece under the surface hard layer becomes thicker, and the compressive internal stress is also improved, thereby making the workpiece more resistant to fatigue and fracture. The high frequency induction heating machine is easy to install on the production line, easy to realize mechanization and automation, easy to manage, and can effectively reduce transportation, save manpower, and improve production efficiency.

High frequency induction heating treatment machine can realize multiple purposes on one machine. It can complete the heat treatment process, such as quenching, tempering, welding, smelting, thermal assembly, thermal disassembly and thermal forming, easy to operate, and can be started or stopped at any time. And no preheating is required. It can be operated manually, semi-automatically and fully automatically; it can work continuously for a long time, or high frequency induction heating machine can be used randomly when in use.

Induction heater bolt remover advocated by the state has high electric energy utilization, environmental protection and energy-saving, safety and reliability, and good working. Portable Induction Heater; Induction Metal heater; heat induction tool; bolt heater tool; Induction Heater Bolt Remover; Induction Heating Steel

If you are looking for more details, kindly visit capacitors for induction heating.